Multi - Parameter Monitor 12.1" Problem - Solutions List

  1. Solution :Check the crimping and continuity of the connector on PCB 12032 (ident J24) and connector on PCB 10005 (ident J14 or J13 or J12)

    Details :Refer Cable PS6

  2. Solution :The two wires soldered to the leg of PCB 12024 are broken, solder them properly.

    Details :Photo of monitor PCB's - Image 3

  3. Solution :The connector from DC-DC PCB 10005 (ident J14 Or J13 or J12) to the Parameter PCB 12032 (ident J24) is faultly. Check voltage - 12v on the DC-DC PCB (10005). Place the multimeter probes on each of the connector pins. If it not coming change PCB 10005v5.

    Details :Refer Cable PS 6 ; Also Refer Photo of monitor PCB's - Image 1 and Reference document for making changes in the unit

  1. Solution :Touch up SMD transistor BC 547 (ident Q5) on solder side on PCB 12032

    Details :Photo of monitor PCB's - Image 4

  1. Solution :Check continuity of 3 pin relimate connector on PCB 12032 (ident J1) to 3 pin connector in Beta LED PCB

    Details :Refer Cable FP4

  1. Solution :Check IC max 232 for dry solder on solder side on PCB 12032, (ident U26) touch up the IC

    Details :Photo of monitor PCB's - Image 4

  2. Solution :Check continuity of D type connector . The D type connector is on the back side of the Monitor

    Details :Refer Cable SP7 and Photo of monitor PCB's - Image 1, Image 2

  1. Solution :Check 40 pin FPC cable is not connected properly, The cable connected from PCB 12032 (ident J21) to LVDS PCB 12021 (ident J9)

    Details :Reference document for making changes in the unit and Photo of monitor PCB's - Image 1

  2. Solution :Touch up the resistor line form ident R222 to R233 on PCB 12032

    Details :Photo of monitor PCB's - Image 3

  3. Solution :PCB 2K12032 (ident J21) 40 pin fpc connector is faulty replace it. Cable flat (fpc) 40 pin, 0.5mm ,length 4 inch

    Details :Refer Photo of monitor PCB's - Image 1

  1. Solution :The two wires soldered to the leg of 12024 are broken, solder them properly

    Details :Photo of monitor PCB's - Image 3

  2. Solution :PCB 12024 is faulty, replace it

    Details :Photo of monitor PCB's - Image 3

  1. Solution :Panel mounting 6 pin ECG input connector on PCB 12032 (ident J2).Check continuity of ECG cable between side plate and PCB , If faulty replace.

    Details :Refer Cable SP1

  1. Solution :Check continuity of the encoder. If faulty resolder the wires or replace the encoder

    Details :Refer Cable FP1 and Photo of monitor PCB's - Image 1

  1. Solution :Check the back panel fuse holders must be loose or the wrong fuse is inserted. (Fuse 5 amp slow blow 20mm, voltage rating - 250v)

    Details :NA

  1. Solution :Check continuity between 6 pin relimate connector on PCB 12032 (ident J10) and 4 pin connector on the keyboard

    Details :Refer Cable FP2 and Photo of monitor PCB's - Image 1

  1. Solution :Check if fuse is inserted into the back panel (Fuse 5 amp slow blow 20mm, voltage rating - 250v)

    Details : NA

  2. Solution :Check LED (ident D1) for indication if PCB is turning ON or not ; If the LED on the PCB is turning ON, then PCB is Ok. If the LED does not turn ON, then check continuity Check the input connector continuity (ident J1) on PCB 10004. If there is no conitniuty then replace the cable

    Details :Refer Cable PS1 - Photo of monitor PCB's - Image 2

  3. Solution :Check the PCB 10004 - The thermistor NTC 10ohm (ident NTC), Capacitor (ident MOV) could be burnt. Check and replace

    Details :Refer Photo of monitor PCB's - Image 2

  4. Solution :Check the PCB 10004 - Regulator IC TOP 256 YN (ident U1) is shorted, check and replace

    Details :Refer Photo of monitor PCB's - Image 2

  5. Solution :Check the continuity between 2 pin relimate connector (ident J11) on PCB 10005 to the Keyboard panel

    Details :Refer Cable no FP3

  1. Solution :Check continuity of 6 pin reliamate (Para1005) on PCB 12032 (ident J5)to 4 pin jst on lifeguard module (ident R1)

    Details :Refer Cable SP4

  1. Solution :Touch up SMD transistor BC 847 (ident Q6) on solder side of PCB 12032

    Details : Refer Photo of monitor PCB's - Image 4

  1. Solution :Check continuity of 4 pin relimate connector on PCB 12032 (ident J7) to 4 pin jst connector on PCB 14015 (ident P2)

    Details :Refer Cable SP2.2

  2. Solution :Check continuity of the Spo2 connector (side panel of the monitor) to the PCB 2K14015

    Details :Refer Cable SP2.1

  1. Solution :Coin cell battery 3V (next to buzzer) on PCB 12032 is faulty replace it

    Details :Refer Photo of monitor PCB's - Image 3

  1. Solution :Crystal 32.76Khz (ident X1) on PCB 12032 is faulty, replace it

    Details :Refer Photo of monitor PCB's - Image 4

  1. Solution :While replacing the ring place a single drop of 'Fewi quick' in between the ring and side panel. And tighten the the nut on the inside of the panel. And Lock it completely

    Details :NA